We make an array of durable construction tools and accessories, including staplers and nailers for siding flooring framing finish and roofing, which are similar to items by Makita, Bostitch, Senco and Dewalt. Trigger mode is when you squeeze the handle to pre-set the staple gun and then switch the knob to Trigger mode. Put the staple gun on the work surface and squeeze the handle to set it. Just like a staple gun. When driving staple into hard surfaces, there is a mode for more power. When driving staple into softer surfaces or in applications where the staple does not need to be driven flush, the mode is for less power. Drop In Staple Loading is when you place the staple in the track with the staple legs facing up. Arrow T50 or Surebonder are used. Arrow T50 or Surebonder are used.
👤This is not a good review. I get 4 miss-fires to 1 actual staple when it is full of staple, but it works when it is full of staple. I stapled hardware cloth to wood and the stapler didn't go far enough into the wood, so it loosened. I was able to cock it and pull the gun. It helped me since I don't have the strongest grip, so squeezing before firing the staple is much easier for me.
👤After putting up my Christmas lights, I realized that staple guns had to have advanced technology since I own one. After using my staple gun, there were 6 string of lights around the perimeter of my fenced in yard. The sucker did not miss a beat. Since I got it, I have been keeping a record of everything. The quick-release is a god send, not just for the sake of your hand, but for when you can't see very well, and you have to shoot something. I showed my father-in-law to me, thinking he'd laugh at me.
👤I use this to stretch canvas onto wood frame bars. I can use my left hand to hold the canvas in place while I use the right hand to pull the gun on the staple gun. The pressure behind the staple is enough to penetrate the wood. I needed a third hand to apply pressure on the staple gun with other models. It is a great tool.
👤This was used for restoring a speaker grill project. The function allowed me to precisely line up the staple on the edge of the frame, which is a thin piece of wood. If you want to use it like a traditional staple gun, it works in that mode as well and has two different "power" settings. I was able to hang my Christmas lights on the house because it was set on low. It will drive a staple in a piece of pine if it is set on high.
👤It's easy to use, but you have to push down at a certain angle for the staple to go all the way in. I had to use a hammer on most of them. I replaced dining room chairs. It was hard to use this in some of the angles I had to get to. The safety feature made me feel comfortable. It was easy to find staplers that fit. They were cheap too. I went to a store.
👤I was a bit skeptical of the reviews. The staple gun works well. I was attracted to it because of the design innovations. The bottom loading makes sense because it allows for a lot more accurate staples. It's a lot easier to squeeze action with my previous staple gun.
👤I wouldn't be able to purchase it if I didn't like it, but it wouldn't keep me from doing so once I've used it.
👤It's good for tight spaces and one hand operation.
WORRY-FREE 2-year-warranty is what quality assurance is. Before using the nail/staple gun, please read the instructions carefully. They will reply within 24 hours if you give them any questions or suggestions. TheSpiral-Drive Technology is Cordless. The brad nailer stapler has a spiral-drive technology that makes it more powerful than a corded tool. The electric nail gun/staple gun can deliver up to 1100 full power shot per full charge, powered by the NEU MASTER 20v MAX battery which has passed 1000 charging cycle test. The brad nail is 18 gauge and the crown staple is 1/2'', which makes it ideal for fastening lightweight decoration trim. Non-Marring rubber nose provides a complete finish. The handle is designed to combat grip fatigue during strenuous tasks. You can illuminate a work area and take your staple gun/nail gun anywhere you want to go with the belt hook.
👤I bought this for a home project. It worked well. I am very happy with the purchase. Other reviews said that it didn't put the nail in the coffin. I did not have that problem. It is battery operated and does not have an air hose or compressor. I used this for a couple hours at a time and the battery only lasted for one dot. I am sure it would last all day. I've already recommended this to a friend. I am happy to have this tool in my collection.
👤I almost didn't get this gun because of the number of reviews that said it didn't have enough power. I'm happy I took my chances. I loaded it with 1 1/2 inch nails, and it went through all the way without any problems, as you can see in the video. If you let the nail push the gun back, it will not go through all the way. If you only have one hand, make sure you press the gun firmly. The weight of the gun will do most of the work, but you still need to apply pressure. I inquired about the battery and contacted customer service. They responded to my reply in less than 24 hours. Excellent service. This gun is very good. They seem to be out of stock if you need a replacement battery.
👤I don't write a lot of reviews. I was not worried about the off name brand. Wow! This is the second best tool I've ever used. The battery was charged and the indicator was nice. I drove at least 400 18ga staplers. I was attaching a wire mesh to the wood and about 30 staplers didn't penetrate all the way into the wood. On day two, drove another 400 12 18ga staple through 1/2 plywood and into 2x4. There were very few bad staples. Wow! I would purchase this product again. 100% BLOWN AWAY!
👤After fully charging the battery, I decided to test it out on a drawer. If you put too much clothes in the drawers they will fall out. The old stapler was pulled out and nailed away. 2/6 nails went all the way in. The other 4 were not sticking out as much. This was a waste for over $100. Put the money towards a better make/model if you return this product.
👤I have never used a nail gun. I was a little concerned with my size and ability to maneuver. Although I had looked at nailers at Home Depot, I knew they were smaller and better quality, and this one did the job quickly. As far as power goes, it was fine. I finished my project quickly and it did a great job.
👤Overall met my expectations. The offset pin nail position can be difficult to line up your shots, but with practice you can do it. The nailer is not able to set the nails in all of the wood, and requires a nail set to achieve a below surface nail head finished position, but this is minor for light use. I recommend the nailer for small projects, but it is not a pro nailer.
It's used for upholstery, cabinet backs, light trim, carpet assembly, small furniture repairs and woodworking projects. The lightweight design relieves the fatigue of the user during long time work. Convenient operation: safetytrigger lock to protect the workers, easy release latch and easy load magazine for fast loading by one hand, and the magazine can hold up 180 nails. The nails are suitable with 22ga Crown staplers. It's used for upholstery, cabinet backs, light trim, carpet assembly, small furniture repairs and woodworking projects. The working pressure is 70-100PSI and the max pressure is 120PSI.
👤Please don't buy this. The gun is hard to find at a local store. Get something more universal by spending a few more dollars.
👤This little guy is adorable. It is easy to load and never jams. There is a lot of power to penetrate wood and thin metal.
👤It's hard to evaluate when I can't find the staple that fits.
👤The unit is very easy to operate and drive deep into some scrap oak while operating near its minimum input pressure range. The performance and ease of use are very good. The drive depth is adjusted by adjusting the air pressure. Special safety features are not included to prevent firing. It's easy to get the tip in to small and tight spaces with this slight safety disadvantage. It reminds me of air staplers from the 1990s. I was annoyed that it didn't come with a few sample stables to start, but I bought a few of the ones on the same website for a very moderate price. I took a photo of it and it shows the things I tested with it. You can see the setting I used.
👤I already have a 3-in-1 gun that has a crown stapler but it was too large for upholstery work so I ordered this stapler and I really like it. This is the smallest pneumatic gun I have and I love using it. I've used it to replace four dining chair seats and can't wait to use it on something else. This is small and easy to maneuver and get into tight corners. The head is very narrow and has a low clearance. I didn't need it for the seats, but I can imagine that it would be useful in certain circumstances. The verdict was: This gun will make your life easier if you want it to. I think it's a good idea.
👤This is light and easy to maneuver. The safety switch is shown on the 2nd pic. The slide bar can be used to add staplers. That stapler does a better job than a manual one. The gun was very good.
👤This is the second Aeropro stapler that I've received and it's a great unit. I needed a smaller stapler to fix some furniture pieces. The Aeropro stapler is compatible with the T50, but my biggest gripe is with the safety mechanism. The rotating locking design has no detents to keep it in place, and is too easy to accidentally open.
It's great for furniture, upholstery, picture frames, shoes-marking, light duty wood assembly, and a lot more. The power industrial upholstery stapler has a long nose for easy reaching. The exhaust dial allows changing the air output direction to keep away from dust and oil. The stapler is compact, light, and easy to carry. The attached accessories can be used for easy maintenance and repair. Convenient bottom loading for quick replenishment. It accepts 1/3'' crown, 1/3'' to 1/2'' (6-16mm) leg length upholstery. The Long Nose Upholstery Stapler and 1PCS is for 1 Box and is a 22 gauge 71 series stapler. The Long Nose Upholstery Stapler and 1PCS is for 1 Box and is a 22 gauge 71 series stapler.
👤Don't buy from a seller. The product does not come with staplers. The stapler they send doesn't use standard staplers and has a smaller air chamber, so it wouldn't be as powerful if I could find one to fit it. If I could, I would give a zero star.
It's great for furniture, upholstery, picture frames, shoes-marking, automobile interiors, light duty wood assembly, and much more. The pneumatic fencing stapler is designed to drive staple wire. It can be used to secure fencing, pet enclosures, vineyard fencing, snow control fencing, and other applications. This stapler has a belt hook and non-slip comfort grip, an optional T-handle for additional control, and a quick release nose for easy jam clearing. The wire alignment notch and depth adjust allow you to place the staple consistently. They're committed to providing outstanding value, top tier customer service and long lasting, high quality products. From roofing to siding to flooring, they make nailers and staplers. They manufacture tools with the most durable materials that are suitable for professional contractors and do-it-yourselfers alike. Their tools are sold, distributed, serviced, and warrantied in the USA. They make an array of durable construction tools and accessories, including staplers and nailers for siding, flooring, framing, finish, and roofing. Their products are similar to items by Bostitch, Senco, and Dewalt. They make an array of durable construction tools and accessories, including staplers and nailers for siding, flooring, framing, finish, and roofing. Their products are similar to items by Bostitch, Senco, and Dewalt.
👤I wanted to finish up about 600 feet of fencing. I used a hammer. I am an idiot. Had to have bought it right away. The last 200 feet were completed in one day. I used a harbor freight 100 psi pancake compressor to run the gun. The compressor works well. I used a bit of air before I started. The gun is easy to use. It was probably 1 in 30. It failed if I put it with staplers. I pulled the staple feeder to get it to fire again. It jammed a few times. Pull the air hose off, pull the clip on the gun's nose, and print it back together. I realized it was the stapler after the second jam. Some of the ones I got had too much glue on them. I began to remove the over glue ones and he was fine. A good purchase. I would recommend it.
👤I recently bought a hobby farm and was tasked with installing nearly 2 miles of fencing. I was sweating bullets when I thought of pounding in thousands of staplers. The freeman staple gun is in! It is a huge time saver but it has some quirks that make it a bit difficult to be a perfect tool. 1. You have to do a lot of work to oil it. When it started acting up, I noticed that a quick shot of air tool oil would bring it back to normal. The balance is quite good and it is heavy. It is just plain heavy. 3. The staple loading process is a little frustrating and I believe the spring holding the staple in the slide could be stronger to reduce the jams and misfires. 4. I wish it held more stapled objects. A longer slide would have been awesome, but only if you buy it and deal with the quirks. It is a life saver.
👤I've had 2 of these staplers. I build a split rail fence on the side and don't want to pound 1000 fence staplers on an average fence. Life is too short for that. I bought this stapler and was very happy with it. Even if it was a one-off project, I would recommend this product. The product and 2 people can put 1000 odd in a fence in about 1 1/2 hours. We use it to hang wire mesh. Depending on the person's skill with a hammer, it would take up to 8 hours. I have had 2 of these staplers. The first was not good. It wouldn't feed. I had to push the mechanism that pushes the staple into the chamber after every fire. It was very frustrating. It blew the bid due to my hired labor needing to be on site much longer than anticipated and it took 888-349-8884 The casting on the top of the magazine was rough and wouldn't feed the staplers as they were intended. I called customer service and was expecting more trouble. Within 5 minutes, I had a human on the line who was very helpful. They immediately said they would send a new unit after I explained the problem. There was no fight or hassle. I sent the dud back because the new unit arrived in a timely manner. I was happy with the resolution. I used the new unit on 2 fences and 2200 staplers. It is best to use the same brand of fastenings. The unit works well. The unit still mis-fires even with regular port oiling. I would have an issue with every single stick. A failure to feed is a mis-fire. The hammer/striker that pushes the staple into the wood doesn't like to fully withdraw. I would apply oil to the area of the strikers hole every 30 minutes for the rest of the year. When the failure to fire started to happen more often, I would stop, unhook from air, oil, rehook to air, and resume work. It's annoying when working at a production pace. It works great when the unit works. It hits hard and sinks fully. The electric compressor kept up with the constant use and I had it hooked up to it. It is good, but there is one small quibble. As you use the unit, the gasket between the body and rear of the unit will wear away at your skin. To some pain. I shaved it off with a knife. It shouldn't be an issue if you wear gloves. The weight is reasonable. The sky hook has stops in the rotation and is a good length. I didn't have to worry about it going somewhere because I hung it off my bags. The exhaust rotates. It's great if you are firing upside down, something we needed to do a lot. I have had issues with the stapler, but I have been happy to have it. It saved me hours of hammering and my fingers from being broken. The price point is reasonable and I think it's a good value. I don't expect much more at the price point, but I do wish it performed better. You get a Honda when you buy a Honda. You get an Acura when you buy an Acura. If the product is not enough to impress me, I'll be looking at other pneumatic tools from Freeman in the future.
2 in 1 nail gun kit. 1200 staple and 400 nails are included in the package. It's easy to load, and you'll be ready to use it after you get the box. It's suitable for tacking into a variety of materials. There is no limit to your imagination. Fix a few loose items around the home by decorating a canvas frame. It is made of lightweight materials and has a user-friendly design. The electric nail gun can work for long periods of time. No compressor, hose, or wire is needed for this upholstery stapler so that you can take your staple gun anywhere you want. The stapler is compatible with the T50 from 1/2 - 9/16 inch. It has a quick-release loading magazine on the bottom of the gun that can be used to quickly and easily install staplers and nails. It has a transparent window for monitoring staple levels. The settings for safety. The safety switches on the electric staple gun ensure that you have the safest operation. The indicator light will turn green when it is ready to shoot. The staple gun should not be used during charging. The power switch should be turned off when not being used. Lithium battery andusb charge The electric stapler is powered by a battery and can shoot up to 850 staplers per charge. The fabric staple can fire up to 50 pins per minute. The electric nail gun needs only 2 hours to be fully charged. The indicator lets you know when it's fully charged. They have a one-year warranty. If you have a question, please contact them.
👤It was in the box. Finally used it. 3 months later. I am a transplant patient. I am always in and out of the hospital. It took me a long time to open it. I was waiting for the temp to drop so I could be in the attic. I was installing insulation. I charged it. I tried to turn it off. Nothing charged it again. Nothing. The person is dead. Can not return. Too late. My loss.
👤I gave it time to charge before I tried it. I'm going to have to buy another gun because I'm trying to glue vinyl fabric onto particle board with T-50 staplers. This one is only penetrating a small area.
👤I wanted to recover my dining chairs. It wouldn't make it through one cushion before losing its entire charge. It's worthless. I threw away the packing when I returned it.
👤The stapler only has enough force to drive the staple in the surface. Unless the surface is made of styrofoam. It doesn't work when trying to staple anything to the ceiling, it will only shoot out air, and it doesn't matter which of the two options you choose for the staple gun. I used my hammer to drive the staple into the surface after the 1st staple, but it was only able to drive one staple in 100% after the first staple.
👤The electric battery staple gun won't work after the battery discharges at 11 staple.
👤It drives in t-50 3/8 inch staple into panneling with wood behind it. The fully charged part is the bad part. You can't leave it on the charge overnight. After charging it, I put in 6 staplers. It worked great. The project was finished the next day and there was no charge left. The green light was on. The gun went off as soon as I pulled it. I am buying a new gun.
👤It's handy for getting in tight places. I don't like 4V charging.
👤The electric staple gun is well built and I can't say anything bad about it. I needed to get something inexpensive to make it easier to insulate a large attic space because my hands were getting ache from using a manual staple gun. This is a great modern design and takes standard T-50 staplers. I wasn't expecting much more. It works so well, it works loads from the bottom unlike traditional staplers, and the charge lasts. I have yet to charge after hours of work. If you have a limited budget, I highly recommend this workhorse. It gets the job done and looks great.
👤The product is small and light for lady hands.
The 22-gauge crown is connected to fine wire. Long lip fits into tight spots. It's ultra-light for ease of use. Oil is kept off fabric by the rear exhaust. Rounded steel cap that won't get caught in fabric. Rounded steel cap that won't get caught in fabric.
👤I wanted a stapler that could handle wider crown staplers. The crown. This stapler is used for a short time. Depending on what you are using crown stapler for, it makes a huge difference. I am using it to install insulation and a plastic barrier. Other staplers only support a small portion. A wider crown staple is needed because crown staple would shoot straight through the plastic. Uses very little air. My compressor only needs a setting of 50 to operate and I only need to cycle on every 5 staple loads. The safety lever must be held down to fire. I like it because I just hang the gun and hose over my shoulder and position what I am doing. I don't have to worry about the gun accidentally shooting or putting a staple in my back. The natural way of holding the gun and pulling thetrigger is unaffected by the safety lever. It is light and comfortable. There is a It is easy to get into tight spots because it is small. The website of Senco is very informative. Pick your model and it will show you what staplers are compatible with your stapler. You can get the stapler at any hardware store. I got mine from Home Depot.
👤It works great, I replaced the fabric on a bunch of speaker grills and it worked great. It's small and light and can be used in tight places. Only a few of the 500 staplers have been fired so far.
👤I was frustrated with the electric stapler that I had. My husband assured me that the pneumatic stapler and small compressor would be worth the money. He was correct. The SENCO stapler is very easy to use. I have arthritis in my hands but have no problem handling it. I like the fact that I can hold the stapler away from the material to put things in place. I had to call the customer help line twice to get some advice on setting up. They were helpful with detailed explanations and questions on usage to make sure I had the correct hose. This is the best tool I have, and it's true that it's the right tool for the job.
👤This is a piece of professional equipment. I am attaching the plywood to the beech wood in a large model boat. The idea is that the staplers hold the wood in place while the glue cures. The boat stringers have very little impulse to impart to the staplers. Staple force can be adjusted with variations in air pressure. It will staple to its full depth, so it can staple smaller pieces. Too little pressure results in the stapler skipping. They are easy to load. The tool seems to give long service in home use. The tool is lightweight and easy to use.
👤I purchased this wire stapler because of my neighbor. I used to use this tool to put up screening on my back porch. The older model works just as well as the new one. I am very pleased with how the stapler works and how it feels in my hand. Excellent tool.
Push the side button to adjust how far you want the staple to go. These staplers are not disruptive as other brands are, but they are lower pitched and more acceptable. The process of every stapling only lasts an instant, which is one more difference from other small stapler and large stapler that staple slowly yet runs loud as hell. It uses standard 22 ga. The crown staple is from 1 to 9mm in length. For ease of operation, small and lightweight. Features a comfortable grip. The magazine and jam release are easy to load. It's ideal for cabinet assembly, fabric applications, light wood assembly, silk screen assembly, and screen door replace. The air compressor was not included. It's ideal for cabinet assembly, fabric applications, light wood assembly, silk screen assembly, and screen door replace. The air compressor was not included.
👤I made the mistake of assuming that the ad was for the T50 size staple. It is likely that KT stands for T50 staplers.
👤I needed one fast so I bought this. It arrived quickly. I was surprised at how good the quality was. It worked well in tight spots. I had to keepunlocking it because the safety was accidentally pushed so it was a little annoying but a great value. I have purchased better quality ones from my distributor. This stapler should work for many different needs.
👤I am very pleased with my first pneumatic stapler. I did not have a single jam or misfire on the 6 hard wood dining chairs and 1 office chair. Not a single staple was wasted. I usually have to use a hammer to tap a few in, but it was a lonely sight for these projects. Not a single staple was needed to be inserted. I have been using the product on Amazon and they are very clean and tight. It's to be expected with 22 gauge wire. There is a The nose is long and precise. Even with my arthritis, the loading is single handed. Highly recommended.
👤Whatever comes along, use for upholstery couch, chairs. I love doing it. This stapler is great. It's easy to handle because it's small. The staples are just right. Would buy again and recommend.
👤The stapler is doing everything I expected it to do and I am happy with it. The quality of the build seems to be solid and after re-decorating twenty chairs it is still working well. I run this at 60 psi and it drives the staple through the thick fabric. This is a great tool for the person who needs a pneumatic stapler. There is no safety, that is the only thing that is odd to me. All my nail guns, pin nailers, etc, you have to press the nail gun tip onto the surface to make sure you don't get hurt. The gun does not have that. You have to keep your finger off the gun. It has a safety that is not like most other nailers. I don't think this is a bad thing, just something to be aware of. I recommend this stapler to the DIYer.
👤I know how much staple guns cost, but I was skeptical. I needed an extra gun because I was broke. This is a great stapler. It's perfect for lightweight fabrics and vinyl, and it's the same as those projects where your regular gun blasts the right staple through the fabric and sinks them into the wood? This is the gun you want. This is a good starter gun if you're a new to upholstery or just starting out. It's also good if you're not sure if you want to go ahead with it, and this is the right gun for that. I'm happy. I switch back to my heavy duty gun when I have to go back and bang the staples the rest of the way down. It is the same gun as my other one. The only complaint I have is that the safety is a silly little thing that is in the way when I hit it, and sometimes I hit it by accident. I will take it off completely. It's all over. This is a great stapler.
The electric staple gun should be kept in vertical operation. The contact point switch and binding material need to be pressed tightly, two-handed, to penetrate the nail. Can prevent stuck nails. Not recommended for baseboards, quarter round, drywall installation, roofing and flooring. The electric stapler gun and brad nailer 2-in-1 kit has a lightweight design, no compressor, no noise, strong power, and is very convenient to use and carry. It's suitable for do-it-yourself projects and upholstery of lightweight material and cork. Two-in-one upholstery stapler gun is widely applicable to cork, general repair, do it yourself crafts, decorations, cardboard, insulation materials, cloth, leather, thin plates and other fastening applications. 18 GA brad nails can be used from 1/2'' to 5/8'' and from 1 to 9/16''. The appropriate size of nails/staples is determined by your needs. They know the importance of safety, contact safety switch design prevents accidental triggering, need to turn on three protective devices at the same time to start the machine and shoot nails, very safe design. Will not cause injury due to operating errors. Even if you are a novice, it is easy to get started with lightweight upholstery staple gun operation. The handle is soft and comfortable. The copper wire motor can drive 45 rounds per minute, more efficient, and the observation window can be used to see the number of nails to load. It has a certification that assures after-sale service. Before use, please read the instructions carefully. The 180-day return service guarantees a hassle-free shopping experience.
👤Ise est escalera. I trabajo 5 estrella.
👤This stapler was bought to recover a bench. The staple gun was easy to use and the price was right. I didn't need an extension cord like I did with another staple gun because it has a nice long cord. I liked the stapler removal part of it. The only reason I didn't give it 5 stars was because I had trouble with the stapler going into the wood frame of the bench. The bench was made from very hard wood and it was difficult to remove the old staple. I had to hammer a few punches to get them to go in to the hard wood. I was very pleased with this staple gun and staple remover, and I would recommend them to anyone.
👤The product works well. I had battery items because batteries go dead. The electric staple gun works well.
👤Would not fire a single staple. Some garbage is included in the instructions. The item is back.
👤The staple gun is also a nail gun. I used a non powered staple gun before purchasing this gun. It was a lot of work to use it. Press it down and squeeze the gun to fire. So far, so good!
👤I make things as a hobby. I have carpal tunnel in the other hand and had surgery on my hand that limited the strength in my hand. I told you that this staple gun was a life saver. I couldn't have completed that canvas without it. It took me a while to even want to attempt to make the canvas, but the ease of my EWORK made it so simple, I am getting ready to complete many more of the canvas and anything else that has to be stapled. Thank you so much.
👤The staple removal is great. The stapler is easy to use, but requires a couple of millimeters to pound. About the same with manual staplers. I am not sure what the small nails can be used for. The bundle is cheaper than the one bought alone.
👤We wanted to put vinyl on the staircase. We wrapped the vinyl around the treads. The stapler was not strong enough to drive a standard T50 stapler through a plywood tread. Returned.
The dial is easy to use for a wide variety of finish applications. Anyone with or without previous experience can use it. This electric stapler can be used as both a staple gun and brad nailer, and can be used with insulation, carpet padding, ceiling tile, and picture frames. Super lightweight The electric staple gun is lightweight and comfortable to use, making it perfect for ladies or children to handle with their crafts. 900 pieces of T50 staplers (8mm, 10mm, 12mm) are widely used. The power tool is perfect for styling and nailing of cardboard, insulation material, fabrics, foils, leather, corkwood and etc. The electric hand tool is designed with triple lock mechanism for extra security and safety, and it has a comfortable handle. WORRY-FREE-12-month-warranty is a quality assurance. For use in North America. Before use, please read the instructions carefully. They will reply within 24 hours if you have any questions. WORRY-FREE-12-month-warranty is a quality assurance. For use in North America. Before use, please read the instructions carefully. They will reply within 24 hours if you have any questions.
👤This product is wonderful. I live alone and am 65 years old. I paid 20 dollars for one manual stapler a year. I couldn't use it. I don't have the strength to push and pull the gun. I bought an electric one. I have used it on a lot of projects. I used the nailer on the base boards. This is very easy to use. I have used a box of staplers and it has not gotten jammed. One of these is what every woman needs.
👤Light weight and usable. My hands are damaged. This tool is very useful. Love it. It is cute.
👤I ordered a stapler to use to restore the loveseat. It has two straps. I knew I needed to be as close to a pneumatic stapler as possible after using a manual stapler. I was very nervous about ordering this. I was wrong. This product is great. My life was made easier by the lightweight feel. It holds a short stack of staplers, but the overall performance is better than that.
👤I bought a staple gun to replace my Arrow gun. The stairs leading from the 2nd story deck became very slippery. My grandson bought us some rough roofing tar paper and was going to put it on the steps, but I wanted to use the gun and do it myself. I stapled each stair down and cut the paper to fit it, I feel safer going down the stairs now. The gun never jammed, I used a lot of staples and it worked.
👤An awesome person when doing something. Simple to use, powerful and easy to use.
👤It was much better than expected. I was reloading frequently but I was able to staple my chicken wire to fencing. It is better than my last stapler, which was much more heavy duty, but sometimes went all the way through other times. Light weight.
👤The KeLDE Electric Staple Gun is not a tool. I read reviews and decided to try it out on a few chairs. What a mistake! It wouldn't go through the thin wood that was the foundation for the cushion. It would go through anything with more substance than thin cardboard. I bought a pneumatic stapler after returning it.
👤I like the safe lock design because it protects me and anyone who will use it. It's very easy to penetrate my wood plank and handles. A case of nails is provided.
👤Stanley solo me dur 1 ao y medio, se empez a trabar. The funciona bastante, es ms chica y ligera. No pesa, no calidad de ensamble, no grapa excelente.
👤The product was supposed to come with 300 and 900 pieces of nails. I received a staple gun. There is false advertising. Will not buy from this seller again.
The Pneumatic Stapler Kit has a Carrying Case and Finish Stapler. The pneumatic fencing stapler is an ideal tool for installation of your fencing project, it weighs just 8 lbs and features a comfortable T-handle and belt hook. The stapler has an optional T-handle for added control and a wire alignment notch to ensure correct placement on fencing. They make nailers and staplers for every purpose from roofing to siding to flooring and everything in between. They make an array of durable construction tools and accessories, including staplers and nailers for siding flooring framing finish and roofing, which are similar to items by Makita, Bostitch, Senco and Dewalt. They make an array of durable construction tools and accessories, including staplers and nailers for siding flooring framing finish and roofing, which are similar to items by Makita, Bostitch, Senco and Dewalt.
👤I was researching a pneumatic stapler that would be used for cattle fencing and I saw that some brands were around the high $800 mark. It was too good to be true at $359 on Amazon with a couple of good reviews. I've had some good buying experiences through Amazon, so decided to go for the low dollar unit, even though I sometimes wondered if the more expensive one would be more reliable, easier to use, and last longer. The issue I had at the point of buying this staple gun was that the blocks of fencing that were put to the gun on the Amazon site wouldn't fit it. I learned that I needed to source StockAde '9 gauge' staplers that don't appear to be available on Amazon for some reason, after reading other helpful comments. I got some advice from there and ordered a box of 1200 staplers from McArthur Lumber in Ohio to test my new tool. It took eight days for the staple to arrive in Texas, and the package was heavy, so it was knocked about by the time I got it. Southwest Agriculture Supplies in San Antonio is a good place to buy the staple if you're looking for a little more locally grown. I contacted them to arrange my tax exempt status here in Texas, and have been happy to be able to order one day and receive the staple the next. This is a good option for those in the southern states who want to avoid long distance shipping. The link for the staple is at southwestagriculturesupplies.com/products/stock-ade-st-400-pneumatic-9-gauge-fencing-staples-class-3 I've never had a jam or a problem. Like me, I have miles of pasture fencing that is getting old. I don't have the ability to replace them, and they are getting tired. I was raised in New Zealand and spent three decades in Australia, so I looked at the fencing systems there and decided to adapt them to my fence in Texas. batons are attached to the wires between my posts. I have to cut them myself out of the pine, then I have to attach the batons to the fence. I put a gas-powered compressor on my old trailer that I brought from Australia, and a retractable air hose on it to give me a good range before I move the trailer forward. There is a ratio of five or six barbed wires per baton. The staple gun has pushed out over 2000 staplers. I apply pneumatic tool oil to it every day. I bought some from a retailer and the bottle with the tool has no way to keep the cap on when it's clipped to open it. It took some time to get the technique right and to work out a few things with the gun. You need to press it down against the wire against the baton to push the nose-bridge back. A barb in the way can be a problem. If you haven't noticed that the clip is empty, it won't fire, so you can push the nose against the post and wonder why it won't fire. It's relatively light, but with a full clip and the fact that I have to use it on it's side, it makes your hands and arms tired after a while. After easing myself into the task, I found that I could keep at it for a long time. I can highly recommend this staple gun. I will update this review if there are any issues with the batons that I will install over the next couple of months. March 31, 2016 Update as promised... I am very happy with the 9000 staple run through this gun. The mechanism on the nose of it that automatically springs back for reloading failed to spring back at some point. I didn't have time to send the gun away from repairs, so I made a small spring that sits on the side of the magazine slide and drilled a hole in it. It works well. The second problem was a staple jam that one tried to come out backwards. I don't know how this happened. I was happy to see that the staple wasn't bent after I gently tapped the bolt/plate. I had to take the staple out in two pieces with some bolt cutters because I had to nip it in half. I had to quit work and come back to clear the jam. The gun just keeps on keeping on. Highly recommended!
Electric long nose upholstery stapler products from Surebonder. In this article about electric long nose upholstery stapler you can see why people choose the product. Neu Master and Aeropro Tools Inc are also good brands to look for when you are finding electric long nose upholstery stapler.
Surebonder, Neu Master and Aeropro Tools Inc are some of the best brands that chosen by people for electric long nose upholstery stapler. Find the detail in this article. China-top Silver, Freeman and Populo are also brands that their products are worth to check.