Best Electric Outboard Motor 3hp

Motor 31 Jan 2023 10+ Comments Open

1. Newport Vessels Trolling Battery Center

Newport Vessels Trolling Battery Center

The battery ports are safe and easy to connect to the motor or accessory. The circuit breakers are integrated with 10 Amp and 60 Amp circuit breakers. The directusb charger and accessory port is a convenient way to connect various DC accessories. The product is 17 x 12 x 10 inches and is compatible with Group 24 and 27 batteries.

Brand: Newport Vessels

👤I have had this product for about a year and I must now completely echo reviews like kTosTIUGA's on 6 17 2017: Exactly the same thing happened to me, all the way to melted plastic and stripped terminals. The terminals were heated up by using it with a motor. Just like KTos, the wing nuts stopped functioning and the connector just spun around inside the plastic, 6 months ago. I could only run it at lower speeds when it cut out and died after a few minutes. I smelled plastic and the wing nut terminals melted out of the case. I opened the electronics/wire compartment and it seemed fine, except the main terminal connections were melted plastic and the connections were useless. I don't have any problems with the motor when it's run directly from the battery. This is a dangerous product and can cause a fire on the boat or damage your trolly motor. I never used all the gizmo connections, but I was afraid to plug my phone in for fear of damage after using the main terminal.

👤I decided to build a solar generator, looked at individual power components and bare battery boxes and decided for the cost and features of the Newport vessels, it would be easy to build. There is plenty of room for a small charge controller and 600 watt pure sine wave inverter to be put in the box. The build quality and output features on this box are top of the line. The box is portable and easy to carry with the large carry handle. The last solar generator I built took four hours to build, and it looked less than nice. This box is a great deal.

👤This is the second box I have returned. Other buyers have reported that the first one had faulty terminals. The one I got did not fit my battery. It began to rust before it saw the ocean. A customer service representative said that I was making it all up and was spreading false rumors about telephone conversations I had with Newport Vessels. I had a 55 pound motor that failed on their maiden voyage. Be careful. The company sells cheap and unreliable products.

👤The terminal post on the replacement pulled out one week after receiving the replacement. The product is pretty. I can't ignore reality. The design is for a product that won't get bumped or moved around. I don't know what caused the damage. I pulled a wire. The terminal posts aren't securely attached. There should be a large backing plate inside the housing. I was debating about making an update. The product is too fragile to be of service to me. Terminal posts are attached to large cables that can get bumped or pulled when placed in a location for easy access, and I am not gentle with my equipment. We have to do that to be able to use the features. I don't recommend this product. I have only been frustrated by it. The design needs to be updated to securely mount the posts. The cables should be secure enough to be able to be pulled. It is a matter of time before they are pulled out. I am a fisherman andDurability is a key factor. This product is not good enough for me, and is not worth repairing. I don't expect another replacement and I won't ask for one. My education and loss. My motto is to get the best and forget the rest. Everyone can read my earlier report. I am proud to update my status and brag that I have what I want. I was unable to submit my claim because the terminal post came lose on my battery box. I posted my original review after I realized I had exhausted the resources available to replace the box. Newport vessels monitored customer reviews. They were very concerned when they saw my review, and they wanted it to be a lot more positive. Their intervention to maintain their reputation is worth 5 stars in my opinion. That is important to me. The difficulty that I had trying to claim a return/exchange is not the norm. I was invited to call on the telephone by someone from Newport Vessels. I was routed to a real person who said that he wanted to help, but I could tell that he had some reservations. He was careful to not make any promises until he verified the facts. The trolly motor smart battery cases have a full year of manufacturer warranty. He was convinced after I verified the date of my purchase and sent him some pictures. He was committed to customer satisfaction. He made it easy for me to give the information. I submitted my receipt after filling out a claim form. I received a new case within a week. I offered to send my damaged case back in his excellent quality, heavy duty shipping container if he would provide a return label and pay for shipping. He didn't want it. This is the kind of case that I want for my battery. It does an excellent job of protecting my battery, and it provides features that are beyond what is expected in a battery box. I like the built in tester. The amount of charge in my batteries can be quickly checked. I love the fact that I can charge my phone while on the lake, and I also love the fact that I can plug my phone into the charging port. When I bought the box, I didn't even consider one more feature. It's built in circuit breakers. My auxiliary posts are routed through a push button circuit breaker, and I used it a lot. The features are located on top of the box. I don't recommend this power center. The product is innovative, modern, stylish and practical, it's backed by a manufacturer that cares about their reputation. After I gave up on filing a claim for the loss, they reached out and contacted me. I don't see why they wouldn't do the same for you. I hope you don't need that service. We deserve that kind of commitment to our customers. Look at the feature photos that sold me on the purchase. The pictures show off the quality. They sell me on customer satisfaction guarantees. My initial report is below. It has not changed in any way. I know that I'm satisfied now. As of March 2017: I immediately put my marine battery into it. There are a couple issues with this case. There are accessory posts attached to the top of the box. They are not strong. I don't know what happened to mine, but I didn't do anything to damage it. My topside posts are not connected. The terminal post turned and came away from the case after a short connection. The cable is not accessible. I thought I might be able to fix it. I can't remove the protective plastic cover because I can't access the wiring inside the lid. I have problems using them. Sometimes the connection is good enough to start the motor, and other times, I have to remove the top and move it to an angle to get the current flow. The test meter only says that the charge is low when I try to use it. It says low even when it is fully charged. I want to replace it with something that has terminal posts. I will probably try to tear the protective plastic cover apart to get access. Try to find something with better quality. I guess it needs to be more durable to give access to make repairs. I think you will love this piece of equipment. Good luck. I hope my information helped you make an informed decision. "Get the best and forget the rest!"

2. Newport Vessels Saltwater Electric Indicator

Newport Vessels Saltwater Electric Indicator

Extra long cables allow for different battery placement. This electric motor provides 62lb thrust and is great for any boater. The motor can run all day without overheating or making noise, thanks to the high quality build. Features: The motor has a 40 inch shaft, a 10 LED battery meter, a 6 inch telescoping tiller handle, and a 3 blade propeller. When needed, the mount angle, height, and direction can be adjusted. The top speed of the motor is about 4.25mph, it depends on your boat shape, weight, water, wind, and other factors. The 3 blade propeller has a low end. The motor requires a 12V Lead-Acid Deep Cycle or a Li-ion Deep Cycle battery. The motor should have a 60amp circuit breaker at all times. Max Amp Draw: 58A. The Newport motors are made with high quality steel, magnesium, and zinc hardware to resist freshwater and saltwater environments. Every product they make is backed by a 2 year warranty. The Newport motors are made with high quality steel, magnesium, and zinc hardware to resist freshwater and saltwater environments. Every product they make is backed by a 2 year warranty.

Brand: Newport Vessels

👤The broken handle section was taken apart. There was a broken piece that held it all together. There was a ball bearing. They didn't know where they went. I decided to drill a new hole and secure the handle with a bolt after an hour of trial and error. The telescopic function works again despite being poor designed. -2 stars for engineering, -2 stars for broken pieces, and -2 stars for my time. I can still fish. The 86 pound version is portable and has extra power. It did a good job. Good for tooling on a lake, but the seas are too rough. The gears controlling the speed gave out. I have a harder time stopping it now that I can barely get it going. That is dangerous. It's ridiculous that they used cheap plastic on the motor. I fear it is useless in its current state. Manufacturing failure was the only thing that happened. The system requires two batteries. If the goal is kayak-style-launch portable, that's a lot to carry around. wasted money is caused by failed controls.

👤It was a great season. The device is described as saltwater and promises "stainless steel", but there's no indication that it's actually "marine" steel. Within a year, the internally rusted had seized up. Very disappointing. I used it for a 20ft sailboat because I was in a busy marina with a lot of tourists, first-time paddleboarders, people renting kayaks, etc., and I wanted to actually sail in it. The motor was perfect until it wasn't anymore.

👤This pushes my heavy Glassply at fast speeds. The mount and the set screw fittings are very light. The ones on my 40 lbs are the same as the ones on these. The motor had to be light so people could carry it. The motor is powerful. It is difficult to lock the motor straight ahead because of the engine's power. The Newport is small. I have to keep a hand on the engine to steer it while I troll. The whole structure could be stouter. I'm worried.

👤It's amazing so far. Pushes my dingy with me and my lady in it and a cooler with no problems. It ran for 3 hours and was full of charge. Quality wires and connections make this light and variable. Comes with a circuit breaker. Our speed was at least 6 mph if not more, although it wasn't needed all the time.

👤It's not a common brand, but it's a good one. I'll give it to the Newport vessel, we have an 86lb thrust motor on our pontoon. We had 17 people on our boat and we're using only this motor. It has power. It is worth the money. I'm happy we bought it. We were out for almost 5 hours and still had a full battery. We ran it at different speeds. Didn't need to go faster than that. The motor is very strong. You will not regret it. This is the main motor on our pontoon. Right away, it worked out great. The handle and shaft is great. Newport needs to address a couple of cons to improve their product. You'll be great if it's waterproof. The difference between faster and slower speeds isn't much. Something needs to be fixed in the motor. Don't take your boat out in the wind. Someone had to pull us back with their motor. The wind doesn't like fighting it. I think this relates to the speed that doesn't seem different at different settings. The motor was good for the price. If you need a motor that has higher thrust. This is a good bet. When buying, keep in mind the few quirks.

3. Newport Vessels Saltwater Electric Trolling

Newport Vessels Saltwater Electric Trolling

If you don't like their outboard motor carts, you can get their very penny back. The kayak shaft has a fiberglass shaft that allows for variable depth placement. Variable speed is 8 speeds with 5 forwards and 3 reverses. TheTelescoping Handle puts you in total control of your ride. The aluminum motor head is durable and has zinc, magnesium, and STAINLESS-Steel hardware for saltwater use. Extra long cables allow for different battery placement.

Brand: Newport Vessels

👤The troling motor is amazing. I built my own transom mount for my sit on top kayak, and it works like a dream. We went fishing for 5 hours on the lake, and then went around the water. I put a 100 Amp hour battery in my kayak, it looked like a motor boat on the water, on setting 1 it looked like a fish prowler. This thing is up to my expectations. You can't go wrong with this.

👤I returned the motor because it was too heavy for installing to the side of the kayak, and I went with a transom mount instead. I wish I had bought this motor for my canoe instead of the Watersnake brand because it doesn't need the shaft cut. Although it may seem trivial, I like that this motor comes in grey even though it's saltwater rated. I decided to buy the Newport Vessels NV Series motor again because my original kayak motor died on me, so I didn't want to waste time and money returning it for warranty service. I made it 888-282-0465 as you can see from the pics, I made it 888-282-0465. It's very quiet and fast. I fished for 5 hours, covering about 4 miles, with the last 2 miles returning to the launch at full speed. I have two small 35AH batteries in parallel and had 70% charge left when I got home and put the batteries on a charger, so this motor is really light on the juice. It's fine on the stern despite my initial impression that it was too heavy for a kayak. The batteries are stowed in the bow compartment so they don't weigh as much. The Bullnose Rudder provides a big improvement in tracking and turning. It's nice to just use it as a rudder to steer when drifting. The motor works well and looks good. I'm going to buy the same motor for my canoe as well as the 36-lb version for other smaller kayaks.

👤The Newport vessels are 55 lbs. The Lifetime Sport Fisher kayak has a trolling motor. It is mounted to the kayak using a Lifetime kayak mount. The Newport Vessels trolling motor is powered by a 114-amp hour Everstart Maxx deep cycle marine battery and can troll for hours on the slower speed settings. The battery range goes down considerably at speeds of 4-5. It doesn't feel flimsy because it's quite heavy. I usually take it out on the bay. The Sport Fisher tracks like a battleship and I installed a Bullnose rudder to improve tracking. I would trade stability for speed on any day of the week. I wouldn't put too much faith in the display on the handle. The Minn Kota Power Center battery box has a battery meter on it. I have never run out of juice when I start with a fully charged battery. After taking it out four times, I noticed that the motor was not in reverse. I had to go to the Newport Vessels website to get product support. I received an email asking me to file a warranty claim. The customer service and warranty department is second to none. Newport Vessels took care of me after I sent them proof of purchase, pictures of the motor, and a description of the problem. This type of confidence in their products and outstanding customer service is rare in today's market. Newport Vessels has earned a lifetime customer and restored my faith in them.

4. Intex Motor Mount Inflatable Boats

Intex Motor Mount Inflatable Boats

The metal-gear housing has increased reliability. The motor mount kit is for inflatable boats. You can attach up to 3.5-hprs. Made of plywood with aluminum support arms. Attaches and detaches quickly. Most newer model index boats are compatible.

Brand: Intex

👤It was very easy to put together. It seems good for the excursion 5 boat. The electric trolly motor I bought should fit perfectly. Everything came with it. Would recommend!

👤It's easy to install, but first time is awkward, but after you get the feel for it, it's no problem. Also, note: It does work as intended, however I noticed that my motor was too strong and would pull on the mount causing the plastic mount to be pulled up. I drilled my own holes on the mount and now it doesn't pull at all.

👤I finally tried the motor mount. It fit perfectly on my Excursion 4. Everything was included for the assembly. The assembly is straight forward. Bolts with nuts are provided for securing the boat. I think I will replace them with hitch pins. It's important for my inflatable raft to inflate to almost completely inflated, then install the mount, and finish inflating after. It helps.

👤One nut was missing. I contacted them. I was asked to fill out a missing parts report online with a copy of the receipt. I did that. No one came back to me. The report had incomplete requirements, but it was too late as the warranty had expired. This is the worst customer service ever. Don't buy. You should throw your money in the toilet.

👤It was purchased just days before an outing in a lake that prohibits gas engines. There is an inflatable on top of it. Assembly and installation is easy. There were no problems with the Minn Kota motor. The transom was stable at all 5 speeds. Instructions were not needed for the assembly and install.

👤It holds a 2.5hp outboard. It is easy to install and mount.

👤The price on Amazon was great. It arrived a day earlier than expected. I decided to install longer upper support rods to better fit the weight of the motor after watching videos of suggestions.

👤The deal was great but the first day use was broke.

👤It looks like the pictures when put together. We got a Seagull outboard that worked and we couldn't wait to try it out. We have an Intex Seahawk 2 dinghy. It's made of light tubing and plastic. It arrived quickly as well. Very happy with it.

👤Good construction. I have a Honda that comes in under the max recommended weight and power on an Intex mariner 3. The motor is low in the water when upright.

👤I thought I was buying a molded plastic one, it was wooden and it fit my boat, but I didn't read the reviews, so I got the one I got, it seems to be made of quality materials, and it works well. You could probably make one very easy. I wish I had.

👤The mount is good. It's easy to put together and fits my dinghy.

👤The intex motor and excursion 5 can be used. It works well. The grooves could be cut so that they lock in with the intex motor mount grooves.

5. Minn Kota Freshwater Transom Trolling

Minn Kota Freshwater Transom Trolling

The product is 17 x 12 x 10 inches and is compatible with Group 24 and 27 batteries. The solid 10-position lever lock brackets feature a quick-release lever lock and reinforced material that resists flexing, warping, and UV damage. The six-inch Telescoping Tiller is a great way to get easy, comfortable, intuitive operation of your trolly motor. Five speed settings for forward and three for reverse are included. Extra power is delivered to push throw heavy vegetation with this prop. There is a prop pin, nut and washer. The Minn Kota trolling motor has an indestructible shaft at its core. They guarantee it for life.

Brand: Minn Kota

👤The headline was meant to be about the minimum power for the small boat application. I have it hooked to a Sun Dolphin boat. My calculation was that more power was not needed. I need those lower speeds for things. I need to make sure that I can get back in, less paddle, when I go out. The deal is here. The thing isn't a power hog. This is a wet year. Having to stay on the water all the time has been a test for me. I haven't pulled out the battery yet. If you have a 14ft boat, this engine is adequate. If you're on a budget, you don't need to break the bank. It is perfect for my purposes. The thing tilts. I have fought with those releases. Not so on the MinnKota Endura Transom Mount. I have never seen a smooth one. The reverse is not perfect. Don't run it from the back of the boat. Ain't happening. I don't know if the blades are pitched right or not, but the reverse really froths the water without giving much. It will back you out of the shallows, but not for full time use. It works like you want it to. About the handle. I put my motor in the back because I was worried about steering. You know, twisting around. The extension handle made it easy to pull out a lot or a little. I think I might like it better now that it's on the air. One heads up. If you plan on putting a transducer on the foot, be aware that it won't fit as the foot is too short. To get my transducer near to vertical, I put it against the fin and put rubber pads on the edge of it. The depth finder works just fine. No harm was done. Anything that won't rot could be used. For instance, your wife's Tupperware. You will also like my MinnKota Endura Transom Mount Trolling Motor. If you have a small boat, grab one. You will be thanked by me.

👤Works well! Make sure you put an inline fuse on the hot wire. The motor will be saved. I used a 30amp. I got caught in a weed bed. I burned up the motor after it blew the fuse.

👤Can't wait to get on the water after hooking it up to my kayak.

👤The power of stealth for my Sundolphin 2. Even with a load of dive tanks, moves it with ease. After a month of serious abuse, it was still going strong after being rammed into the rocks.

👤It is easy to install and run this motor. I put it on the Seahawk 2 and Seahawk 4. The Endura C2 30 has plenty of power for my max load application, which is me and 3 kids in a big boat, a total of 700 lbs, with the motor, battery, people, and fishing gear. I juice it with an Everstart marine battery with 750MCA, and we can go for around 3 or 4 hours at speed 3, and still have 50 percent left on the battery. It has a nice kick when clicked into speed 5. The Minn Kota has quality at every turn. It has easy controls, including click speed control, tilt shaft, depth control, and steering lock/tightening. I can't hear the motor running. My eight year old is carrying it. The only thing I can say is to upgrade the battery connection. It has a terminal end that can be used to bolt on the battery. I like a plug style one so I can easily remove the motor from the battery box. For my rig, the terminal end may work for others. The Minn Kota Endura C2 30lb is a great motor, and the price is right.

6. Carbhub Evinrude Seahorse Outboard 1981 1992

Carbhub Evinrude Seahorse Outboard 1981 1992

100% satisfaction or your money back! Any quality-related issue can be covered by the 12 months warranty. They will reply within 24 hours. The part number is . Johnson Evinrude Marine 6hp 8hp 9.9hp 15hp Seahorse Engine Outboard 1981-1992 Evinrude 1969 25hp, Johnson 1965, older 70's 25hp are also included. The package includes a fuel pump and gasket. The new part is high quality. The new part is high quality.

Brand: Carbhub

👤Product arrived quickly and was exactly what it was described. The fuel line connections were at different angles that the original pump was causing my existing lines to be just long enough to reach with stretching. The lines need to be replaced to reduce strain. The item was thicker than the fuel pump and the screws on it wouldn't work with the normal gasket. I had to make a gasket out of some spare parts that were very thin and I was able to get 3 or 4 turns on the screws. I can easily fix the problem with some new screws, so not knocking it for that. I would have given this 5 stars if the fuel line connections weren't different. The motor started and ran after I worked through the issues. I am working to fix the lean sneeze condition that I was 800-273-3217 The issue was present before the new fuel pump, so it's unrelated. I'm happy with the purchase since I found the same item on other websites for less than 100 dollars.

👤I squeezed the fuel bulb and the gasket on the front housing was leaking. Checked the tightness of the screw on the housing. It was secure. The fuel pump is bad and should not be sold on Amazon. I have to return the item because I have to get a refund. I had to research other options and pay 135 for an original OMC part. I have stopped buying cheap outboard parts on Amazon. The seller and Amazon should be ashamed. I thought I would see for myself after being warned by other buyers. Thanks to Amazon, I can't have my backup engine until I get a legit part.

👤This fits older Evinrude. I just installed a new computer on my old one. I had to get longer screws. This motor was made in America and bolted right up. The engine is running. I will get the OMC part from marineengines.com now that I have solved my problem. I asked the seller if it would fit my motor, they said no, but it will fit at least 25hp, with 2 longer screws, from the 60s and 70s. It might fit more models, but I know what I am talking about.

👤I was quoted $150 for a pump for my horse. I looked at this one for the fifteen horse and it looked the same as the one on my motor. This one is a little different than the other one I ordered. The bottom of the motor is different. I took the bottom from the new one and swapped it for the old one. Wow, what savings? Thank you so much!

👤I swapped the back plate from my Evinrude 15 HP for it. I watched several videos on the internet to make sure it was done correctly. It didn't function. After many hours of frustration, I found that one of the little valves inside was not functional. I tried to fix the issue, as one of the springs was jammed in. It didn't function. The old pump worked great after I disassembled it and put all of the gasket and springs into it. The gasket and springs are a perfect match for the pump. Either buy a rebuild kit or purchase the Sierra pump. You will end up doing it anyways.

7. COP Propeller Evinrude 309 64106 0 309641060M

COP Propeller Evinrude 309 64106 0 309641060M

The new aftermarket tilt andamp; trim motor was built to meet the specifications of the original Evinrude motor. The inner bore diameter is 12mm. Fit Tohatsu/Nisssan 2-strokes with 2.5hp and 3.5hp. Mercury Johnson/Evinrude has a 3.3hp outboard. The material is made of nylon and plastic. This is a propeller that has been used before. The diameter and pitch are the same as the original ones. The performance and quality are guaranteed by them.

Brand: Copkingo

👤The fit is a bit sloppy with a little more play than the stock, but it is definitely an improvement over the platic prop. Would probably buy again.

8. Johnson Evinrude Outboard CARBURETOR 0114808

Johnson Evinrude Outboard CARBURETOR 0114808

The Inverter Duty Rating Variable Torque is 20:1. The engine is in the Outboard Mode. Check the part number before purchasing it for Johnson Evinrude OMC. For Johnson Evinrude models, BE, BJ, E, J, HE, HJ, SE 2 HP, 3 HP, 3.3 HP, and so on. Assy Intake 2-stroke. Assy Intake 2-stroke.

Brand: Itaco

👤The choke levers and throttles are smaller and do not reach through the plastic.

👤I bought a new carburetor for my outboard. First pull!

👤Nice product. The motor runs great when bolted right on. I think it's a good idea.

👤This is not for a 2hp johnson.

9. DB Electrical TRM0016 Evinrude Johnson

DB Electrical TRM0016 Evinrude Johnson

The trim motor has a 12V rating. The source of the rotation is the aftermarket. The unit type is tilt and trim motor. The original numbers are replaced with the following: ARCO MARINE: 6208, ARROWHEAD: 430-20008, and EMP PARTS: MERCURY MARINE: 802509, OMC: 0172655, 0172847, 0172850, 172655, 172850, 173596, PRESTOLITE. 18-6767-1,WAI:10801N EVINRUDE: E 100, E 100ML, E 100WTL, E 100TX, E 100WML, and E110ML. The one-year warranty protects you after your purchase. Their products will work perfectly in your vehicle. They'll replace it if it doesn't work within one year of your order. They will help you if you have a problem, and they will replace you if you don't. The new aftermarket tilt andamp; trim motor was built to meet the specifications of the original Evinrude motor.

Brand: Db Electrical

👤Bad business when there is a missing gasket and drain bolt.

👤It works. It was great to find a product for the 1975 Evinrude that is at my doorstep in 2 days.

👤This is a great product and the company that makes it, DB Electric, will definitely do business with them in the future.

👤The 70hp evinrude is not long enough to fit into the pump gear. The part will bolt to the add-on tilt. on the motor. There was a waste of time and money.

👤It worked out great. Everything was pictured. Excellent quality.

10. MATI Handlebar Control Headlight 59V 83973 09 00

MATI Handlebar Control Headlight 59V 83973 09 00

The boat propeller has a diameter of 7.4 inches. 59V-83973-00-00 is a replacement part for the manufacture part. Fit for Yamaha Big Bear 350 YFM350F 1987-1992. The MOTO-4 350- YFM350 was released in 1991. Engine start and switch engine run off are functions. A left handlebar switch is packed in a box. If there is a problem with a product within a year, please contact them. Product service is provided by them. If there is a problem with a product within a year, please contact them. Product service is provided by them.

Brand: M Mati

👤The product was described. The product was packaged in a way that it wouldn't be damaged.

👤The starter button didn't work. Junk.

👤It works perfectly plugged into the wiring harness.

👤It was a perfect fit. The product and service were great.

11. Reservoir MERCURY MARINE 819479A1 819480A1

Reservoir MERCURY MARINE 819479A1 819480A1

The lower unit has a powder coating finish. Run with a marine deep cycle battery. 2 years of warranty coverage. Please verify your original unit's part number to make sure it's compatible with MERCURY, SIERRA MARINE and many more. ARCO MARINE: There are two types of TRIM motor, one is a Mercury, the other is a sledgehammer. There is a gun connectors and hardware kit with it. With O-R. Weight: 8 lbs. The computer was tested for reliability and quality. The trim motor has a 12V rating. The source of the rotation is the aftermarket. The trim motor has a 12V rating. The source of the rotation is the aftermarket.

Brand: Rareelectrical

👤There was a problem with the yellow fill plug. The old plug was used on the new one.

👤So far, it works like an original. It was easy to install on my outboard.

👤It was installed that night and it works great, hope it lasts for a few years. Thanks.

👤It works well so far, but can't fill all the way up.

👤It stopped working after I used the boat a second time. Plug leaks should be filled. Very disappointed.

👤We were very happy with the after market lift/trim motor and replacement from Rare Electrical. The unit took about 20 minutes to install. We saved a lot of money on this. The cheapest Mercury brand unit we could find was just under $500.00 and we would have to wait for a couple of weeks for it to be shipped. We are back on the water after getting this one in two days.

Summary

What is the best product for electric outboard motor 3hp?

Electric outboard motor 3hp products from Newport Vessels. In this article about electric outboard motor 3hp you can see why people choose the product. Intex and Minn Kota are also good brands to look for when you are finding electric outboard motor 3hp.

What are the best brands for electric outboard motor 3hp?

Newport Vessels, Intex and Minn Kota are some of the best brands that chosen by people for electric outboard motor 3hp. Find the detail in this article. Carbhub, Copkingo and Itaco are also brands that their products are worth to check.

You May Like

Share Your Story

Your name:
Choose product to comment:
Write your review:
By submitting this review, you are agree that:
  • Your review is based on fact, honest, polite and not harmful to anyone or any brands.
  • We have full right to show or not-to-show your review after moderation.
  • No spamm please :)
Disclaimer
We might earn comission for your shopping via our links, it doesn't cost you extra. This website is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for sites to earn advertising fees by advertising and linking to Amazon.com